Merrychef error codes: what they mean and what to check

Find your code, match it to your oven model, and see what your team can safely check before calling. One code can stand for different faults depending on the model.

72 entries · 69 codes and messages

Safety first. Sparks, or the crackle of electrical arcing: switch the oven off and do not use it again before a technician has examined it. Never take a cover off. Parts of the microwave circuit can stay charged at a dangerous voltage after the oven is unplugged.

eikon e2s and conneX operating faults

Codes that stop the oven or interrupt cooking on the eikon e2s and on the conneX 12 and 16.

E088 Supply voltage out of range

eikon e2s and conneX 12/16

What happens
A warning about the supply voltage comes up on the screen.
What staff can safely check
Tell us if other equipment on the same circuit is misbehaving, or if the kitchen is running on a generator.
What a technician inspects
The kitchen’s electrical supply and the connections where it enters the oven, then the circuit on the power board that measures the voltage.

Call about E088Request a repair

E101 Microwave power does not start

eikon e2s and conneX 12/16

What happens
Preheating can go through as usual. The oven then stops at the first recipe step that needs microwaves, because the controller finds no microwave current where it expects some.
What staff can safely check
No safe check for staff. Note the full message and call.
What a technician inspects
The whole microwave supply, in order: the voltage coming in, the microwave fuses, the door interlock switches and the power board, then the high-voltage transformer, capacitor, diode and magnetron, with every connector between them. The code by itself is no proof that the magnetron has to be changed.

Call about E101Request a repairMore about E101

E102 Heater still drawing current after being switched off

eikon e2s

What happens
The heater has been told to stop, yet the controller goes on measuring current through it. In some older eikon manuals the code has a wider meaning: any heater current that is not what it should be.
What staff can safely check
No safe check for staff. Note the full message and call.
What a technician inspects
The circuit that switches the heater, its wiring and the power board.

Call about E102Request a repair

E102 Heater on without request

conneX 12/16

What happens
The conneX raises this code when the cavity stays 75°C above its set point for more than 30 minutes, or exceeds 300°C.
What staff can safely check
No safe check for staff. Note the full message and call.
What a technician inspects
Cavity temperature probe and its connection on the I/O board, heater switching circuit, and I/O board.

Call about E102Request a repair

E103 Electronics compartment too hot

eikon e2s and conneX 12/16

What happens
It tends to show up after many cooking cycles back to back, or when a nearby appliance blows hot air into the oven’s intake.
What staff can safely check
Clean and refit the air filter below the door. Make sure nothing blocks the air intake and that no hot equipment is blowing onto the oven.
What a technician inspects
The air filter at the front, the fan that cools the electronics, the air inlets and outlets, and anything hot standing close to the oven.

Call about E103Request a repairMore about E103

E104 A thermal safety cutout has opened

eikon e2s

What happens
Cooking stops and the screen reports overheating. Several different safety devices can raise this one code.
What staff can safely check
No safe check for staff. Note the full message and call.
What a technician inspects
The high-limit thermostat of the cavity, the thermostat on the magnetron, the thermal protection of the convection fan motor, and the cooling air path.

Call about E104Request a repairMore about E104

E104 The cavity’s high-limit thermostat has cut out

conneX 12/16

What happens
Cooking stops and the screen says the cavity overheat protection has tripped.
What staff can safely check
No safe check for staff. Note the full message and call.
What a technician inspects
That thermostat and its connections, the temperature actually reached in the cavity, and the convection air flow.

Call about E104Request a repairMore about E104

E105 Supply frequency fault

eikon e2s and conneX 12/16

What happens
The screen reports that the frequency of the electricity supplied to the oven is wrong.
What staff can safely check
Tell us if the kitchen is running on a generator or has had power cuts.
What a technician inspects
The kitchen’s supply, and the generator if the kitchen runs on one, then the circuit in the oven that monitors the supply. Both manuals also list interference from an internal microwave leak as a possible cause, so the technician carries out a microwave leakage test and checks the cavity thermocouple. Older eikon ovens use E105 differently: see the separate entry.

Call about E105Request a repair

E106 Cavity hotter than its set temperature

eikon e2s and conneX 12/16

What happens
The cavity gets up to the set temperature, then keeps climbing past it.
What staff can safely check
Look through the door for burnt food or residue. If you see smoke or flames, switch the oven off, keep the door closed and call.
What a technician inspects
The circuit that switches the heater, the convection fan with its speed controller, and the connection of the cavity thermocouple. The cavity itself is examined too, for food or residue that has started to burn.

Call about E106Request a repair

E107 Lost communication between touchscreen and power board

eikon e2s and conneX 12/16

What happens
Either a communication error comes up on the screen, or the controls no longer react.
What staff can safely check
No safe check for staff. Note the full message and call.
What a technician inspects
The cable that links the two boards and its connectors, then the boards themselves: the touchscreen controller (called QTS on the e2s, UI on the conneX) and the power board (SRB on the e2s, I/O on the conneX).

Call about E107Request a repairMore about E107

E108 Touchscreen configuration module cannot be read

eikon e2s

What happens
The oven’s configuration cannot be read by the touchscreen controller.
What staff can safely check
No safe check for staff. Note the full message and call.
What a technician inspects
The personality module on the QTS and its contacts, then the touchscreen board itself.

Call about E108Request a repair

E108 Fault on the user interface storage card

conneX 12/16

What happens
An error about storage, or about the SD card, comes up on the screen.
What staff can safely check
No safe check for staff. Note the full message and call.
What a technician inspects
The microSD card of the UI board, how well it sits in its holder, and the UI board.

Call about E108Request a repair

E109 Power board configuration module cannot be read

eikon e2s and conneX 12/16

What happens
The power board is unable to read its own configuration. The code can show up after a board has been replaced or the oven serviced.
What staff can safely check
No safe check for staff. Note the full message and call.
What a technician inspects
The personality module, and the way it is connected to the SRB on the e2s or to the I/O board on the conneX.

Call about E109Request a repair

E110 Control board firmware versions do not match

eikon e2s and conneX 12/16

What happens
The screen reports that two versions do not go together, usually just after a board was changed or the software updated.
What staff can safely check
No safe check for staff. Note the full message and call.
What a technician inspects
Which firmware version each board runs: the touchscreen controller on one side, the power board on the other.

Call about E110Request a repair

E111 Fault on the cavity temperature probe

eikon e2s and conneX 12/16

What happens
The cavity temperature reading disappears, or the oven shows a temperature far too high to be real.
What staff can safely check
No safe check for staff. Note the full message and call.
What a technician inspects
The thermocouple in the cavity, its connector and wiring, and the input on the control board that reads it.

Call about E111Request a repairMore about E111

E112 Fault on the power board temperature sensor

eikon e2s and conneX 12/16

What happens
The screen reports that the temperature sensor mounted on the electronics board is faulty.
What staff can safely check
No safe check for staff. Note the full message and call.
What a technician inspects
The ambient temperature sensor on the board, and the board that carries it (SRB or I/O). This is not the probe that measures the cooking cavity.

Call about E112Request a repair

E113 Microwave current present while microwaves are off

eikon e2s and conneX 12/16

What happens
Microwave current is measured although the controller has not asked for microwaves. Take the oven out of use and have it serviced.
What staff can safely check
Stop using the oven and call.
What a technician inspects
Power board (SRB on the e2s, I/O board on the conneX): both manuals direct the technician to replace it. On the eikon e4s the manual names a short-circuited triac, diode or relay on the SRB.

Call about E113Request a repair

E115 / E117 Magnetron too hot

eikon e2s

What happens
Cooking is cut short, and the screen may ask for the front air filter to be cleaned and put back. Which of the two codes appears depends on the firmware the oven runs.
What staff can safely check
Clean and refit the air filter below the door. The oven asks for this itself.
What a technician inspects
The air filter at the front, the cooling fan and the flow of air through the intake, then the magnetron and its thermostat.

Call about E115Request a repair

E116 Convection heater does not respond

eikon e2s and conneX 12/16

What happens
Heat is called for, but the oven may never finish preheating or get to the temperature selected.
What staff can safely check
No safe check for staff. Note the full message and call.
What a technician inspects
The heating element, the supply feeding it and its connectors, and the output of the power board that drives it.

Call about E116Request a repairMore about E116

E117 Right-hand microwave system too hot

conneX 12/16

What happens
The screen reports that the magnetron on the right has overheated, and may ask for the filter to be checked.
What staff can safely check
Remove, clean and refit the air filter below the door, as the on-screen message asks.
What a technician inspects
The thermostat of the right-hand magnetron and its connections, the cooling fan, the air filter and the air intake.

Call about E117Request a repair

E118 Left-hand microwave system too hot

conneX 12/16, where fitted

What happens
The screen reports that the magnetron on the left has overheated.
What staff can safely check
Clean and refit the air filter below the door.
What a technician inspects
The thermostat of the left-hand magnetron and its connections, the cooling fan, the air filter and the air intake.

Call about E118Request a repair

E-1 Internal error, no detail given

conneX 12/16

What happens
An internal error comes up on the screen. Copy the whole message down, above all if X510 appears in it.
What staff can safely check
No safe check for staff. Note the full message and call.
What a technician inspects
The firmware of the controller and the oven’s event history. If the message names X510, see the entry that follows.

Call about E-1Request a repair

E0 / E-1 with X510 in the message Jumper missing on the I/O board

conneX 12/16

What happens
Right after the I/O board has been replaced, the screen says a configuration jumper is not fitted.
What staff can safely check
No safe check for staff. Note the full message and call.
What a technician inspects
The jumper at position X510, and how the new I/O board has been configured.

Call about E0Request a repair

Door open “Door open” stays on screen with the door closed

eikon e2s and conneX 12/16

What happens
The screen keeps showing a door-open message although the door is shut. There is no error code.
What staff can safely check
No safe check for staff. Note the full message and call.
What a technician inspects
Microwave fuse (F2 on the e2s, F5 and F6 on the conneX) and the door interlock switches, which the manuals say to replace if the fuse has blown.

Call about this messageRequest a repair

Touchscreen warnings and event-log entries

Not every line in the oven’s history is a fault: a finished cleaning cycle, a new menu file or the power coming back are logged too. Read each line together with the oven model and the time it was recorded.

E000 Control boards connected

eikon e2s

What happens
The history gains a line each time the control boards start talking to each other, which usually means the oven has just been powered up.
What staff can safely check
No action needed. This is a log entry, not a fault.
What a technician inspects
The QTS, the SRB and the cable between them.

Call about E000Request a repair

E079 / E080 Touchscreen held down

eikon e2s

What happens
The screen has been pressed for a long time. E079 notes that it was let go after a shorter hold.
What staff can safely check
Check that nothing is pressing on the touchscreen or stuck at its edge.
What a technician inspects
The overlay over the touchscreen, anything lodged along the edge of the screen, and the touchscreen unit.

Call about E079Request a repair

E081 Firmware updated

eikon e2s and conneX

What happens
On the conneX the line means the firmware was updated. On the e2s it can stand for an update or for a checksum event.
What staff can safely check
No action needed. This is a log entry, not a fault.
What a technician inspects
The firmware in the controller and the record of past updates.

Call about E081Request a repair

E082 Menu file changed

eikon e2s and conneX 12/16

What happens
A menu file or a recipe file has been updated, and the history says so.
What staff can safely check
No action needed. This is a log entry, not a fault.
What a technician inspects
The menus and recipe files held in the oven.

Call about E082Request a repair

E083 SRB version not compatible

eikon e2s

What happens
The oven has found a power board whose version it cannot work with.
What staff can safely check
No safe check for staff. Note the full message and call.
What a technician inspects
The hardware version of the SRB and the part number printed on the board.

Call about E083Request a repair

E083 Incompatible I/O board version

conneX 12/16

What happens
Listed on the conneX summary sheet as an incompatible I/O board version.
What staff can safely check
No safe check for staff. Note the full message and call.
What a technician inspects
I/O board hardware version and part number.

Call about E083Request a repair

E084 Wrong date at startup

eikon e2s and conneX 12/16

What happens
At startup the controller finds a date that is wrong or not valid, and logs it.
What staff can safely check
Check the date and time in the oven’s settings.
What a technician inspects
The date and time set in the oven; the controller’s firmware too, if the line keeps coming back.

Call about E084Request a repair

E086 Oven turned on

eikon e2s and conneX 12/16

What happens
Someone has started the oven with its ordinary on/off control, and the history keeps a trace of it.
What staff can safely check
No action needed. This is a log entry, not a fault.
What a technician inspects
The on/off control and the history of power events.

Call about E086Request a repair

E087 Touchscreen pressed without a break

eikon e2s

What happens
Something has been pressing on the screen for over 15 seconds, and the screen may no longer react.
What staff can safely check
Check that nothing is pressing on the touchscreen or stuck at its edge.
What a technician inspects
The overlay, any debris caught under it, the way the touchscreen is mounted, its calibration, and the QTS unit.

Call about E087Request a repair

E087 Cleaning cycle finished

conneX 12/16

What happens
A cleaning cycle ran to its end without a problem, and the history notes it.
What staff can safely check
No action needed. This is a log entry, not a fault.
What a technician inspects
The cleaning history. Nothing needs repairing on the strength of this line alone.

Call about E087Request a repair

E098 Cleaning cycle cut short

eikon e2s and conneX 12/16

What happens
The cleaning sequence, or the cooldown before it, stopped before the end. Not every e2s logs this: some firmware versions have dropped the event.
What staff can safely check
Run the cleaning sequence again, to the end.
What a technician inspects
The cleaning sequence and the oven’s event history.

Call about E098Request a repair

E099 Air filter warning ignored

eikon e2s and conneX 12/16

What happens
The oven noticed that the air filter was not in place, and the person using it carried on anyway.
What staff can safely check
Check that the air filter is pushed fully into place.
What a technician inspects
How the filter sits in its slot, the magnet or switch that detects it, then the connector and wiring.

Call about E099Request a repair

E100 Power on, or back after a cut

eikon e2s and conneX 12/16

What happens
Power reached the oven, either switched on or back after a cut, and the history notes the moment. Compare that time with any power cut in the kitchen.
What staff can safely check
No action needed. This is a log entry, not a fault.
What a technician inspects
The electrical supply to the oven and the history of power events.

Call about E100Request a repair

Service-test codes E089 to E097

A technician sees these codes while running the recommissioning test, not during normal cooking. Several steps wait for the person at the oven to do or confirm something: if a prompt goes unanswered the step is marked as failed, although the part itself may be sound.

E089 Cooling fan test

Recommissioning test

What happens
During the test, nobody confirmed that the cooling fan was running.
What staff can safely check
None. This code appears during a technician’s recommissioning test.
What a technician inspects
The fan that cools the electronics and its supply, and whether the test prompt was answered.

Call about E089Request a repair

E090 Convection fan test

Recommissioning test

What happens
The test ended without confirmation that the convection fan was turning.
What staff can safely check
None. This code appears during a technician’s recommissioning test.
What a technician inspects
The motor of the convection fan and its control, and whether the test prompt was answered.

Call about E090Request a repair

E091 Turntable test, where one is fitted

Recommissioning test

What happens
The test ended without confirmation that the turntable was turning. The eikon e2s is not concerned by this step.
What staff can safely check
None. This code appears during a technician’s recommissioning test.
What a technician inspects
The turntable and its drive, on the models that have one.

Call about E091Request a repair

E092 Heater test

Recommissioning test

What happens
The heater did not pass. Depending on the model, the test measures the current it draws or how much the temperature rises. On an e2s the result can appear as E116.
What staff can safely check
None. This code appears during a technician’s recommissioning test.
What a technician inspects
The heating element and the circuit feeding it, and the way the cavity temperature is measured.

Call about E092Request a repair

E093 Microwave test

Recommissioning test

What happens
The microwave current measured is under the minimum the test sets for that model. On an e2s the result can appear as E101.
What staff can safely check
None. This code appears during a technician’s recommissioning test.
What a technician inspects
The circuit that supplies microwave power and the magnetron it feeds.

Call about E093Request a repair

E094 Filter refitting test

Recommissioning test

What happens
The air filter was put back, but the oven did not detect it.
What staff can safely check
None. This code appears during a technician’s recommissioning test.
What a technician inspects
The filter and its magnet, the switch that detects them, and the wiring.

Call about E094Request a repair

E095 Filter removal test

Recommissioning test

What happens
The air filter was taken out, but the oven did not detect it.
What staff can safely check
None. This code appears during a technician’s recommissioning test.
What a technician inspects
The filter switch and its wiring. A switch whose signal stays closed is one cause to look for.

Call about E095Request a repair

E096 Door closing test

Recommissioning test

What happens
The door was closed, but the oven did not detect it.
What staff can safely check
None. This code appears during a technician’s recommissioning test.
What a technician inspects
How the door lines up, then the interlock switches with their connectors and wiring.

Call about E096Request a repair

E097 Door opening test

Recommissioning test

What happens
The door was opened, but the oven did not detect it.
What staff can safely check
None. This code appears during a technician’s recommissioning test.
What a technician inspects
The door interlock switches, the way the door operates them, and the wiring.

Call about E097Request a repair

Other eikon models

Codes whose meaning is specific to the eikon e1s, e2, e3, e4, e4s, e5 or e6.

E086 / E087 Recommissioning test failures

eikon e2 and e6

What happens
On these older models the two codes belong to the technician’s recommissioning test: E086 is the radiant heater test and E087, on the e6, the low heater test. They do not have the meaning shown above for the e2s and conneX.
What staff can safely check
No safe check for staff. Note the full message and call.
What a technician inspects
The heater circuit named by the test.

Call about E086Request a repair

E102 / E103 / E106 Same names, different thresholds

eikon e1s

What happens
The e1s uses the same code names with its own thresholds: E102 for a cavity 25°C over its set point, E103 for an electronics compartment above 60°C, and E106 for a cavity reaching 300°C.
What staff can safely check
No safe check for staff. Note the full message and call.
What a technician inspects
Heater switching circuit, air filter and cooling fan, and the cavity temperature circuit.

Call about E102Request a repair

E105 Supply voltage too high or too low

Older eikon e3 and e4

What happens
In older e3 and e4 manuals, E105 means the voltage reaching the oven is outside its specification. Read the whole message on the screen against the manual revision that goes with the oven.
What staff can safely check
No safe check for staff. Note the full message and call.
What a technician inspects
The electrical supply to the oven and the circuit that monitors its voltage.

Call about E105Request a repair

E114 Code held in reserve

e4s and older eikon references

What happens
In these manual revisions the code is set aside: no operating fault is attached to it.
What staff can safely check
No safe check for staff. Note the full message and call.
What a technician inspects
These references name no component for it.

Call about E114Request a repair

E115 Convection fan feedback reports a fault

eikon e6

What happens
The controller of the convection fan signals a fault over its feedback circuit.
What staff can safely check
No safe check for staff. Note the full message and call.
What a technician inspects
The fan motor and its controller, the feedback wiring, and the SRB input that receives the signal.

Call about E115Request a repair

E115 Convection fan feedback

eikon e4s

What happens
The convection fan speed controller reports a fault. The manual gives a disconnected speed-controller cable as the example.
What staff can safely check
No safe check for staff. Note the full message and call.
What a technician inspects
Speed controller cable and connections, convection fan and its controller.

Call about E115Request a repair

E116 Heater does not switch on

eikon e2, e3, e4, e5, and e6

What happens
From the e2 to the e5 the code means the convection heater has not come on. The e6 uses it for its high heater circuit.
What staff can safely check
No safe check for staff. Note the full message and call.
What a technician inspects
The heating element concerned, the wiring that supplies it, and the SRB output that switches it.

Call about E116Request a repair

E117 Magnetron too hot

eikon e1s, e2, e3, e4, e4s, e5, e6 and conneX 12e

What happens
While microwaves are in use, the thermal protection of the magnetron cuts out. On the e6 the code designates the magnetron on the right. The conneX 12e manual lists E117 for an overheated magnetron as well.
What staff can safely check
No safe check for staff. Note the full message and call.
What a technician inspects
On the model concerned: the air filter and the cooling air path, then the magnetron and its thermal cutout.

Call about E117Request a repair

E119 Low convection heater does not switch off

eikon e6

What happens
The low heater has been told to stop and is still drawing current.
What staff can safely check
No safe check for staff. Note the full message and call.
What a technician inspects
The circuit that switches the low heater, and the SRB.

Call about E119Request a repair

E120 Low convection heater does not switch on

eikon e6

What happens
Low convection heat is asked for by the controller, which then sees no sign that the heater has responded.
What staff can safely check
No safe check for staff. Note the full message and call.
What a technician inspects
The low heating element and its wiring, and the power board output that drives it.

Call about E120Request a repair

E121 / E122 Radiant heater switching

e2/e6 service references

What happens
E121 stands for a radiant heater that stays on, E122 for one that does not start. In the e2 revision that lists them, both are marked as not yet implemented.
What staff can safely check
No safe check for staff. Note the full message and call.
What a technician inspects
On the versions that have one: the radiant heating element and the circuit that switches it.

Call about E121Request a repair

E124 Left magnetron too hot

eikon e6

What happens
While the oven is working, the thermal cutout of the magnetron on the left opens.
What staff can safely check
No safe check for staff. Note the full message and call.
What a technician inspects
The magnetron on the left, its thermal switch and the cooling air path.

Call about E124Request a repair

E127 Fault on the touchscreen board temperature sensor

eikon e2 / e6

What happens
The touchscreen controller no longer gets a reading from the ambient temperature sensor on its own board.
What staff can safely check
No safe check for staff. Note the full message and call.
What a technician inspects
The QTS board and the temperature sensor it carries.

Call about E127Request a repair

Three more codes are named in an older service reference, with no production oven series attached to them in that revision: E118 (bottom fan feedback), E123 (food elevator) and E125/E126 (switching of the left magnetron). E118 does have a documented meaning on the conneX 12 and 16, where it reports the left-hand microwave system overheating.

Mealstream EC401 legacy codes

Display codes of the Mealstream EC401, a legacy model.

E:1 Door detected as open

Mealstream EC401

What happens
The oven refuses to start: it believes the door is open, even when it looks shut.
What staff can safely check
Close the door fully and check that nothing is trapped in it.
What a technician inspects
How the door closes, the interlock microswitches and their connectors, the ribbon cable, and the control boards.

Call about E:1Request a repair

E:3 Time or program not accepted

Mealstream EC401

What happens
The cooking time entered, or the program chosen, is refused by the oven.
What staff can safely check
Check the time and the program you selected.
What a technician inspects
The time that was set, the recipe in memory and the data on the MenuKey, then the keypad membrane and the logic board.

Call about E:3Request a repair

E:4 Cavity not heating

Mealstream EC401

What happens
The cavity stays cooler than it should during heating.
What staff can safely check
No safe check for staff. Note the full message and call.
What a technician inspects
The fuse protecting the heater, the heating element, the high-limit thermostat, and the rest of the heater circuit.

Call about E:4Request a repair

E:5 Cavity too hot

Mealstream EC401

What happens
The temperature in the cavity climbs above what it should be.
What staff can safely check
No safe check for staff. Note the full message and call.
What a technician inspects
The sensor that measures the cavity temperature, and the relay that switches the heater.

Call about E:5Request a repair

E:6 Oven not at the temperature the program needs

Mealstream EC401

What happens
The recipe chosen will not start: the oven is not yet at the temperature that recipe requires.
What staff can safely check
Let the oven reach its programmed temperature before starting the program.
What a technician inspects
The temperature set in the recipe and how far preheating has got.

Call about E:6Request a repair

E:7 Magnetron too hot

Mealstream EC401

What happens
The display says the magnetron has overheated.
What staff can safely check
Check that the air filters are clean and that the oven is not drawing in hot air.
What a technician inspects
The fan that cools the magnetron, the air filters, and any hot air being drawn into the intake.

Call about E:7Request a repair

Wrench symbol Recovery from overheating, or a diagnostic warning

Mealstream EC401

What happens
Either the magnetron overheated and has now cooled down again, or the controller has logged an internal diagnostic problem.
What staff can safely check
Check that the air filters are clean and that the oven is not drawing in hot air.
What a technician inspects
The cooling fan, whether the turntable turns, the filters, and the flow of air through the intake.

Call about this messageRequest a repair

Crossed-lines symbol Controls compartment too hot

Mealstream EC401

What happens
The compartment that houses the controls has overheated.
What staff can safely check
Check that the air filters are clean and that the oven is not drawing in hot air.
What a technician inspects
The axial cooling fan, the air filters, and the temperature of the air going into the intake.

Call about this messageRequest a repair

EPS / FAIL / rEdo MenuKey transfer not completed

Mealstream EC401

What happens
A transfer of programs did not go through to the end. The display shows EPS, then FAIL, then rEdo; on the segment display the S can read as a 5.
What staff can safely check
Switch the oven off and start the MenuKey download again.
What a technician inspects
The MenuKey and the way the transfer was carried out.

Call about this messageRequest a repair

Merrychef 402s display messages

The 402s shows messages in words. The wording depends on the panel version.

ERROR MAGNETRON 1 / ERROR MAGNETRON 2 / ERROR MAGNETRON 1 & 2 Magnetron too hot

Merrychef 402s

What happens
The magnetron named in the message has overheated, or both have.
What staff can safely check
Check the air filters, move hot equipment away from the oven, and do not run it empty.
What a technician inspects
The air filters and the cooling air path, anything blowing hot air near the oven, and whether it was run with nothing in it.

Call about this messageRequest a repair

MAGNETRON 1 FAILED / MAGNETRON 2 FAILED / MAGNETRON 1 & 2 FAILED A microwave channel has failed

Merrychef 402s

What happens
The message signals a fault on one microwave channel, or on both.
What staff can safely check
No safe check for staff. Note the full message and call.
What a technician inspects
The microwave channel named in the message, component by component. Only testing shows which part has failed.

Call about this messageRequest a repair

CAVITY SENSOR ERROR Cavity did not heat, or rose far above the preheat setting

Merrychef 402s

What happens
This message has two documented causes. Either the cavity did not heat up as expected within ten minutes, or it rose far above the preheat setting during cooking (the manuals give 72°F to 90°F, about 50°C), which they treat as a sign of fire in the cavity.
What staff can safely check
Look for signs of burning in the cavity. If you see smoke or flames, switch the oven off, keep the door closed and call.
What a technician inspects
Signs of burning in the cavity first, then the temperature sensor resistance, the heater elements and the door interlock switch. By itself the message is not proof that the temperature sensor is the faulty part.

Call about this messageRequest a repair

AMBIENT OVERHEAT / CAVITY OVERHEAT / HEATER FAILURE Version 3.0 wording

Merrychef 402s, version 3.0 panel

What happens
Version 3.0 panels word their messages differently: Magnetron 1, 2 or 1 & 2 Overheat; Ambient Overheat when the temperature inside the casing exceeds its limit; Cavity Overheat when the cavity passes 565°F; Heater Failure when the cavity has not reached 100°F in ten minutes.
What staff can safely check
No safe check for staff. Note the full message and call.
What a technician inspects
Air filters and cooling airflow for the overheat messages; heater elements and their circuit for Heater Failure.

Call about this messageRequest a repair

When you call

Tell us what the screen says

Have the oven model, the serial number and a photo of the full message if you can, and tell us when the fault appears.

  • Oven modelOn the rating plate at the back of the oven, for example eikon e2s or conneX 12.
  • Serial numberAlso on the rating plate. On the e2s it shows briefly when the oven starts.
  • Error codeThe code and the full message on the screen.
  • A photoOf the screen or the oven, if you can take one.
  • When it happensDuring preheat, mid-cycle, or as soon as it’s switched on.

Where this guide comes from. Entries were checked in November 2026 against the manufacturer’s own service manuals: eikon e2s (32Z3923), conneX 12 and 16 (32Z9170), eikon e4s (32Z3870), eikon e3 and e4, eikon e1s, conneX 12e, Mealstream EC401 and 402s. Meanings can still vary with the firmware and the manual revision.

Free phone estimate

A code on the screen? Call us.

305-447-7384

Monday–Friday, 9 AM–8 PM. For urgent weekend issues, leave a voicemail. Weekend messages are prioritized on Monday.

Prefer that we call you? Leave your number.

Enter your name.
Enter a 10-digit phone number.

We call back during business hours.

Call 305-447-7384 Request